LED Bulb Lamp Light Led Lamp Beads White/Red/Green/Blue/Yellow F5mm 3*7.6*7.6mm

Description

LED Bulb Lamp Light Led Lamp Beads White/Red/Green/Blue/Yellow F5mm 3*7.6*7.6mm
Product Information:
Type: white light
Size: 3.0*7.6*7.6mm
Color temperature: 6000-8000k
Brightness: 2500-3000mcd
Voltage: 3.0-3.2V
Current: 20ma
Quantity: 10pcs/pack
Type: Red light
Size: 3.0*7.6*7.6mm
Wavelength: 620-625nm
Brightness: 1500-2000mcd
Voltage: 2.0-2.2V
Current: 20ma
Quantity: 10pcs/pack
Type: Green light
Size: 3.0*7.6*7.6mm
Wavelength: 520-525nm
Brightness: 2500-3500mcd
Voltage: 3.0-3.2V
Current: 20ma
Quantity: 10pcs/pack
Type: Blue light
Size: 3.0*7.6*7.6mm
Wavelength: 460-465nm
Brightness: 2000-2500mcd
Voltage: 3.0-3.2V
Current: 20ma
Quantity: 10pcs/pack
Type: Yellow light
Size: 3.0*7.6*7.6mm
Wavelength: 585-590nm
Brightness: 1500-2000mcd
Voltage: 2.0-2.2V
Current: 20ma
Quantity: 10pcs/pack
Positive and negative pins:
the long pin is the positive pole, the short pin is the negative pole, and the middle pin of the two-color three-pin is the common terminal. Common positive: the middle foot is positive, common negative: the middle foot is negative.
Promise LED pin: Promise LED is 2 pins
①The long leg is connected to the positive electrode, and the short leg is connected to the negative electrode.
②The short leg is connected to the positive electrode, and the long leg is connected to the negative electrode, and the light green is bright.
LED Soldering Conditions:
(1) Soldering iron welding: The temperature of the tip of the soldering iron (up to 30W) should not exceed 280°C, the soldering iron must be grounded, and the static electricity should not exceed the range. The welding time should not exceed 3 seconds, and the welding position should be at least 3 mm away from the colloid.
(2) Dip soldering: The maximum temperature of dip soldering is 260°C, the dip soldering time should not exceed 3 seconds, and the dip soldering position should be at least 3 mm away from the colloid.
LED installation method:
(1) Pay attention to the arrangement of the external lines of various devices to prevent wrong polarity installation. The device should not be too close to the heating element, and the working conditions should not exceed its specified limits.
(2) Be sure not to mount the LED with the pins deformed.
(3) When deciding to install in the hole, calculate the size and tolerance of the hole and the hole distance on the circuit board to avoid excessive pressure on the bracket.
(4) When installing the LED, it is recommended to use a guide sleeve for positioning.
(5) Before the soldering temperature returns to normal, it is necessary to avoid any vibration or external force on the LED.
Cleaning:
Special care must be taken when cleaning colloids with chemicals, because some chemicals can damage the colloid surface and cause discoloration, such as trichloroethylene, acetone, etc. It can be wiped and dipped with ethanol, and the time should not exceed 1 minute at room temperature.
😃
You can find more products in different material, type, color , sizes and shapes in our shop！ If you have special needs, please contact us, we can customize according to your needs!
P
a
ckage Including:
According to your choice.
Guarantee:
Good Good Good quality. Buy with confidence!
We maintain high standards of excellence and strive for 100% customer satisfaction!